This product was discontinued on: March 27, 2020

0 Replacement products available

NHH-4565C-R2B

6-port sector antenna, 2x 698–896 MHz 45° HPBW and 4x 1695–2360 MHz 65° HPBW, 2x RETs and 2x SBTs. Both high bands share the same electrical tilt.

Specifications

Finish making your selections or clear them to view relevant specifications.

Features and Benefits

Internal SBT on low and high band allow remote RET control from the radio over the RF jumper cable
Separate RS-485 RET input/output for low and high band
One LB RET and one HB RET. Both high bands are controlled by one RET to ensure same tilt level for 4x Rx or 4x MIMO
Hybrid antenna with narrow beamwidth on the low band for superior interference mitigation on the LB and 65° beamwidth on the high band which allows maintaining the good signal coverage at the cell edge for the high band

Specifications

General Specifications

Antenna Type	Sector
Band	Multiband
Color	Light Gray (RAL 7035)
Grounding Type	RF connector body grounded to reflector and mounting bracket
Performance Note	Outdoor usage \| Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material	Fiberglass, UV resistant
Radiator Material	Aluminum \| Low loss circuit board
Reflector Material	Aluminum
RF Connector Interface	4.3-10 Female
RF Connector Location	Bottom
RF Connector Quantity, high band	4
RF Connector Quantity, mid band	0
RF Connector Quantity, low band	2
RF Connector Quantity, total	6

RET Interface	8-pin DIN Female \| 8-pin DIN Male
RET Interface, quantity	2 female \| 2 male
Input Voltage	10–30 Vdc
Internal Bias Tee	Port 1 \| Port 3
Internal RET	High band (1) \| Low band (1)
Power Consumption, idle state, maximum	1 W
Power Consumption, normal conditions, maximum	10 W
Protocol	3GPP/AISG 2.0 (Single RET)

Width	457 mm \| 17.992 in
Depth	178 mm \| 7.008 in
Length	2437 mm \| 95.945 in
Net Weight, without mounting kit	40 kg \| 88.185 lb

Click on image to enlarge.

Click on image to enlarge.

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360
Gain, dBi	17.9	18.2	17.6	18.0	18.3	18.7
Beamwidth, Horizontal, degrees	47	42	62	62	66	66
Beamwidth, Vertical, degrees	9	8.1	5.7	5.3	5	4.5
Beam Tilt, degrees	0–10	0–10	0–8	0–8	0–8	0–8
USLS (First Lobe), dB	18	21	17	19	20	20
Front-to-Back Ratio at 180°, dB	33	39	33	35	35	35
Isolation, Cross Polarization, dB	25	25	25	25	25	25
Isolation, Inter-band, dB	30	30	28	28	28	28
VSWR \| Return loss, dB	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0
PIM, 3rd Order, 2 x 20 W, dBc	-153	-153	-153	-153	-153	-153
Input Power per Port at 50°C, maximum, watts	300	300	250	250	250	200

Effective Projective Area (EPA), frontal	1.4 m² \| 15.069 ft²
Effective Projective Area (EPA), lateral	0.3 m² \| 3.229 ft²
Mechanical Tilt Range	0°–10°
Wind Loading @ Velocity, frontal	1,485.0 N @ 150 km/h (333.8 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral	315.0 N @ 150 km/h (70.8 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum	1,485.0 N @ 150 km/h (333.8 lbf @ 150 km/h)
Wind Loading @ Velocity, rear	1,304.0 N @ 150 km/h (293.2 lbf @ 150 km/h)
Wind Speed, maximum	241 km/h (150 mph)

Agency	Classification
ISO 9001:2015	Designed, manufactured and/or distributed under this quality management system

Antenna Type	Sector
Band	Multiband
Color	Light Gray (RAL 7035)
Grounding Type	RF connector body grounded to reflector and mounting bracket
Performance Note	Outdoor usage \| Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material	Fiberglass, UV resistant
Radiator Material	Aluminum \| Low loss circuit board
Reflector Material	Aluminum
RF Connector Interface	4.3-10 Female
RF Connector Location	Bottom
RF Connector Quantity, high band	4
RF Connector Quantity, mid band	0
RF Connector Quantity, low band	2
RF Connector Quantity, total	6

RET Interface	8-pin DIN Female \| 8-pin DIN Male
RET Interface, quantity	2 female \| 2 male
Input Voltage	10–30 Vdc
Internal Bias Tee	Port 1 \| Port 3
Internal RET	High band (1) \| Low band (1)
Power Consumption, idle state, maximum	1 W
Power Consumption, normal conditions, maximum	10 W
Protocol	3GPP/AISG 2.0 (Single RET)

Width	457 mm \| 17.992 in
Depth	178 mm \| 7.008 in
Length	2437 mm \| 95.945 in
Net Weight, without mounting kit	40 kg \| 88.185 lb

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360
Gain, dBi	17.9	18.2	17.6	18.0	18.3	18.7
Beamwidth, Horizontal, degrees	47	42	62	62	66	66
Beamwidth, Vertical, degrees	9	8.1	5.7	5.3	5	4.5
Beam Tilt, degrees	0–10	0–10	0–8	0–8	0–8	0–8
USLS (First Lobe), dB	18	21	17	19	20	20
Front-to-Back Ratio at 180°, dB	33	39	33	35	35	35
Isolation, Cross Polarization, dB	25	25	25	25	25	25
Isolation, Inter-band, dB	30	30	28	28	28	28
VSWR \| Return loss, dB	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0
PIM, 3rd Order, 2 x 20 W, dBc	-153	-153	-153	-153	-153	-153
Input Power per Port at 50°C, maximum, watts	300	300	250	250	250	200

Effective Projective Area (EPA), frontal	1.4 m² \| 15.069 ft²
Effective Projective Area (EPA), lateral	0.3 m² \| 3.229 ft²
Mechanical Tilt Range	0°–10°
Wind Loading @ Velocity, frontal	1,485.0 N @ 150 km/h (333.8 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral	315.0 N @ 150 km/h (70.8 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum	1,485.0 N @ 150 km/h (333.8 lbf @ 150 km/h)
Wind Loading @ Velocity, rear	1,304.0 N @ 150 km/h (293.2 lbf @ 150 km/h)
Wind Speed, maximum	241 km/h (150 mph)