1. Inicio
  2. Tipo de red
  3. Emplazamientos de célula macro en exteriores
  4. Equipos RET y antenas para estaciones base
  5. Antenas para estaciones base
  6. 2UPX210B-T2
Warning Icon

For other alternatives, please contact us for more information.

0 Alternative products available

2UPX210B-T2

4-port multibeam antenna, 4x 694–896 MHz, 2x 37° HPBW, 2x RET with manual override.

Find a Partner
Specifications
Finish making your selections or clear them to view relevant specifications.
Features and Benefits
  • Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical tilt with manual override on both beams
  • Each port has an integrated bias tee, and each beam has its own smart switch that automatically selects between bias tee or AISG inputs according to a predetermined priority table
  • Single panel design supporting two separate beams perfectly optimized at horizontal pointing angles of +27 degrees and –27 degrees from boresight

General Specifications

Antenna Type Multibeam
Band Single band
Grounding Type RF connector body grounded to reflector and mounting bracket
Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material Fiberglass, UV resistant
Radiator Material Copper | Low loss circuit board
Reflector Material Aluminum
RF Connector Interface 7-16 DIN Female
RF Connector Location Bottom
RF Connector Quantity, high band 0
RF Connector Quantity, mid band 0
RF Connector Quantity, low band 4
RF Connector Quantity, total 4

Remote Electrical Tilt (RET) Information

RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 1 female | 2 male
Input Voltage 10–30 Vdc
Internal Bias Tee Port 1 | Port 2 | Port 3 | Port 4
Internal RET Low band (2)
Power Consumption, idle state, maximum 2 W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)

Dimensions

Width 640 mm | 25.197 in
Depth 235 mm | 9.252 in
Length 2533 mm | 99.724 in
Net Weight, without mounting kit 47 kg | 103.617 lb

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 694 – 896 MHz
Polarization ±45°
Total Input Power, maximum 700 W @ 50 °C

Electrical Specifications

Frequency Band, MHz 694–806 806–896
Gain, dBi 17.9 18.7
Beam Centers, Horizontal, degrees ±27 ±27
Beamwidth, Horizontal, degrees 39 36
Beamwidth, Vertical, degrees 9.6 8.4
Beam Tilt, degrees 0–10 0–10
USLS (First Lobe), dB 21 21
Front-to-Back Ratio at 180°, dB 34 40
Isolation, Cross Polarization, dB 25 25
Isolation, Inter-band, dB 18 18
VSWR | Return loss, dB 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150
Input Power per Port at 50°C, maximum, watts 200 200

Mechanical Specifications

Wind Loading @ Velocity, frontal 1,102.0 N @ 150 km/h (247.7 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral 372.0 N @ 150 km/h (83.6 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum 1,497.0 N @ 150 km/h (336.5 lbf @ 150 km/h)
Wind Loading @ Velocity, rear 1,135.0 N @ 150 km/h (255.2 lbf @ 150 km/h)
Wind Speed, maximum 200 km/h (124 mph)

Packaging and Weights

Width, packed 797 mm | 31.378 in
Depth, packed 402 mm | 15.827 in
Length, packed 2684 mm | 105.669 in
Weight, gross 67 kg | 147.71 lb

Regulatory Compliance/Certifications

Agency Classification
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
ROHS Compliant/Exempted
CHINA-ROHS Above maximum concentration value
UK-ROHS Compliant/Exempted

General Specifications

Antenna Type Multibeam
Band Single band
Grounding Type RF connector body grounded to reflector and mounting bracket
Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material Fiberglass, UV resistant
Radiator Material Copper | Low loss circuit board
Reflector Material Aluminum
RF Connector Interface 7-16 DIN Female
RF Connector Location Bottom
RF Connector Quantity, high band 0
RF Connector Quantity, mid band 0
RF Connector Quantity, low band 4
RF Connector Quantity, total 4

Remote Electrical Tilt (RET) Information

RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 1 female | 2 male
Input Voltage 10–30 Vdc
Internal Bias Tee Port 1 | Port 2 | Port 3 | Port 4
Internal RET Low band (2)
Power Consumption, idle state, maximum 2 W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)

Dimensions

Width 640 mm | 25.197 in
Depth 235 mm | 9.252 in
Length 2533 mm | 99.724 in
Net Weight, without mounting kit 47 kg | 103.617 lb

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 694 – 896 MHz
Polarization ±45°
Total Input Power, maximum 700 W @ 50 °C

Electrical Specifications

Frequency Band, MHz 694–806 806–896
Gain, dBi 17.9 18.7
Beam Centers, Horizontal, degrees ±27 ±27
Beamwidth, Horizontal, degrees 39 36
Beamwidth, Vertical, degrees 9.6 8.4
Beam Tilt, degrees 0–10 0–10
USLS (First Lobe), dB 21 21
Front-to-Back Ratio at 180°, dB 34 40
Isolation, Cross Polarization, dB 25 25
Isolation, Inter-band, dB 18 18
VSWR | Return loss, dB 1.43 | 15.0 1.43 | 15.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150
Input Power per Port at 50°C, maximum, watts 200 200

Mechanical Specifications

Wind Loading @ Velocity, frontal 1,102.0 N @ 150 km/h (247.7 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral 372.0 N @ 150 km/h (83.6 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum 1,497.0 N @ 150 km/h (336.5 lbf @ 150 km/h)
Wind Loading @ Velocity, rear 1,135.0 N @ 150 km/h (255.2 lbf @ 150 km/h)
Wind Speed, maximum 200 km/h (124 mph)

Packaging and Weights

Width, packed 797 mm | 31.378 in
Depth, packed 402 mm | 15.827 in
Length, packed 2684 mm | 105.669 in
Weight, gross 67 kg | 147.71 lb

Regulatory Compliance/Certifications

Agency Classification
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
ROHS Compliant/Exempted
CHINA-ROHS Above maximum concentration value
UK-ROHS Compliant/Exempted